 Kelvin Ly
|
4854120342
|
Generate ibom
|
2020-08-23 10:36:41 -04:00 |
|
Kelvin Ly
|
92d9ff929a
|
Regenerate BOM
|
2020-08-23 10:31:11 -04:00 |
|
Kelvin Ly
|
8e093993f8
|
Modify DRV8304 thermal vias to pass PCBWay's 2 layer DRM
|
2020-08-23 00:20:42 -04:00 |
|
Kelvin Ly
|
9d6f7c3897
|
Generate Gerbers
|
2020-08-22 21:52:37 -04:00 |
|
Kelvin Ly
|
e553a88410
|
Add 3D models for stuff
|
2020-07-25 14:55:07 -04:00 |
|
Kelvin Ly
|
213898ed63
|
Add dimensions and increase battery connector footprint
|
2020-07-25 09:06:03 -04:00 |
|
Kelvin Ly
|
f86027b8af
|
Add more vias
|
2020-07-25 08:00:13 -04:00 |
|
Kelvin Ly
|
273abb7529
|
Regenerate Gerbers with extra STM32F ground via
|
2020-07-14 15:19:25 -04:00 |
|
Kelvin Ly
|
bfd0590a12
|
Generate BOM
|
2020-07-11 21:13:53 -04:00 |
|
Kelvin Ly
|
191228f26d
|
Finish Rev 2 of BLDC design
|
2020-07-11 19:08:13 -04:00 |
|
Kelvin Ly
|
945d1055c2
|
Save before autofill
|
2020-07-10 00:04:31 -04:00 |
|
Kelvin Ly
|
c93169406d
|
Remove FPGA; TODO replace with STM32F303C6T6
|
2020-03-28 17:03:33 -04:00 |
|
Kelvin Ly
|
244d83f43b
|
Save before working on rev.2
|
2020-03-28 16:52:10 -04:00 |
|
Kelvin Ly
|
2b56926951
|
Save changes; remove stencil alignment pins, fix Flash chip connection
|
2020-02-09 14:33:48 -05:00 |
|
Kelvin Ly
|
f66c03cf2a
|
Do some work with DRC8353 driver
|
2020-01-25 20:19:05 -05:00 |
|
Kelvin Ly
|
6b8dc6f337
|
Add a check to make sure driver enable is set
|
2020-01-22 07:47:22 -05:00 |
|
Kelvin Ly
|
5f85a3b99e
|
Work on DRV8353 SPI driver
|
2020-01-22 07:42:50 -05:00 |
|
Kelvin Ly
|
bd108603e3
|
Reorganize testbench a bit
|
2020-01-17 07:40:07 -05:00 |
|
Kelvin Ly
|
d4611c0ea3
|
Replace rtn with rst, start work on DRV3535 SPI configuration
|
2020-01-10 08:23:01 -05:00 |
|
Kelvin Ly
|
20a6482c27
|
Add missing low side current sense lines
|
2020-01-10 08:22:32 -05:00 |
|
Kelvin Ly
|
31d43b5b71
|
Fix bugs in ADC debug code; woah that actually workedgit add .
|
2020-01-08 23:54:54 -05:00 |
|
Kelvin Ly
|
21984a4b1a
|
Boost ADC speed to closer to maximum spec
|
2020-01-08 00:10:12 -05:00 |
|
Kelvin Ly
|
faaf9415a0
|
Start work on testing ADC driver
|
2020-01-07 23:57:08 -05:00 |
|
Kelvin Ly
|
b95e31eda1
|
Add tests to main Makefile
|
2020-01-07 20:29:52 -05:00 |
|
Kelvin Ly
|
008783cc40
|
Add tests Makefile
|
2020-01-07 20:04:58 -05:00 |
|
Kelvin Ly
|
0e67bfc6dc
|
Finish ADC testbench for now TODO check to make sure CS is toggled at the right times
|
2020-01-07 19:58:48 -05:00 |
|
Kelvin Ly
|
9b81123138
|
Add gitignore
|
2020-01-07 19:57:52 -05:00 |
|
Kelvin Ly
|
9b35a04234
|
adc_driver seems to be working to original spec, now to shift the slave select back a few cycles
|
2020-01-07 09:02:04 -05:00 |
|
Kelvin Ly
|
5f2364b5cf
|
Write ADC driver TODO write testbench for ADC driver
|
2020-01-06 08:04:00 -05:00 |
|
Kelvin Ly
|
ad27f2a94c
|
Working UART TX!
|
2020-01-05 16:55:52 -05:00 |
|
Kelvin Ly
|
1b82426037
|
Remove error message on clean
|
2020-01-05 15:34:25 -05:00 |
|
Kelvin Ly
|
3c22edf1a3
|
Annotate pin swap fix (this took two hours to figure out)
|
2020-01-05 15:18:26 -05:00 |
|
Kelvin Ly
|
ee8fbb898a
|
Add 'all' command
|
2020-01-05 15:18:09 -05:00 |
|
Kelvin Ly
|
6b49bb1e11
|
Get ice timing reporting working
|
2020-01-05 15:17:28 -05:00 |
|
Kelvin Ly
|
af286d07ca
|
Generate a usable binary file for flashrom
|
2020-01-05 13:26:54 -05:00 |
|
Kelvin Ly
|
9ae99282b2
|
Update KiCAD project stuff after moving the folder
|
2020-01-05 13:06:57 -05:00 |
|
Kelvin Ly
|
6feb0209a4
|
Mostly working workflow for programming the FPGA
|
2020-01-05 13:06:33 -05:00 |
|
Kelvin Ly
|
f4f8978227
|
Move PCB stuff into subdirectory
|
2020-01-05 11:49:55 -05:00 |
|
Kelvin Ly
|
729ed70f16
|
Replot in old Gerber format
|
2019-12-20 00:43:11 -05:00 |
|
Kelvin Ly
|
e1e79180eb
|
Add stencil alignment pins
|
2019-12-20 00:07:02 -05:00 |
|
Kelvin Ly
|
660d6e96a0
|
Generate BOM
|
2019-12-19 07:43:52 -05:00 |
|
Kelvin Ly
|
997263b979
|
(Rev 1) Generate Gerbers and other output files
|
2019-12-19 07:42:16 -05:00 |
|
Kelvin Ly
|
2d63112cba
|
Footprint fixes done TODO fix silkscreen add mounting holes
|
2019-12-19 00:54:33 -05:00 |
|
Kelvin Ly
|
23ec5016cb
|
Fix Lattice ICE40 footprint stencil stuff
|
2019-12-19 00:50:47 -05:00 |
|
Kelvin Ly
|
207e70493b
|
Fix footprints; stencil masks apparently shouldn't be made from pads
|
2019-12-19 00:43:41 -05:00 |
|
Kelvin Ly
|
7eb8b64bcc
|
Finish out of the layout and routing, TODO fix footprints
|
2019-12-19 00:22:51 -05:00 |
|
Kelvin Ly
|
53afa404db
|
Start work on layout, all footprints done
|
2019-12-01 01:11:50 -05:00 |
|
Kelvin Ly
|
3552a9be1e
|
Add FPGA footprint, save before autofilll
|
2019-12-01 00:43:27 -05:00 |
|
Kelvin Ly
|
379c64f4bb
|
Generate Lattice QFN48 footprint TODO add custom stencil shape
|
2019-12-01 00:34:27 -05:00 |
|
Kelvin Ly
|
e65a76d408
|
Generate some footprints
|
2019-12-01 00:21:06 -05:00 |