diff --git a/grblHAL_Teensy4/src/.settings/language.settings.xml b/grblHAL_Teensy4/src/.settings/language.settings.xml
index 7f5978c..907189d 100644
--- a/grblHAL_Teensy4/src/.settings/language.settings.xml
+++ b/grblHAL_Teensy4/src/.settings/language.settings.xml
@@ -5,11 +5,11 @@
-
+
-
+
\ No newline at end of file
diff --git a/grblHAL_Teensy4/src/T40X101_map.h b/grblHAL_Teensy4/src/T40X101_map.h
index 60c1634..1fa80b4 100644
--- a/grblHAL_Teensy4/src/T40X101_map.h
+++ b/grblHAL_Teensy4/src/T40X101_map.h
@@ -5,7 +5,7 @@
Board by Phil Barrett: https://github.com/phil-barrett/grblHAL-teensy-4.x
- Copyright (c) 2020 Terje Io
+ Copyright (c) 2020-2021 Terje Io
Grbl is free software: you can redistribute it and/or modify
it under the terms of the GNU General Public License as published by
@@ -31,6 +31,10 @@
#error No pins available for encoder input!
#endif
+#if SPINDLE_SYNC_ENABLE
+#error Spindle sync is not supported for T40X101
+#endif
+
// Default pin assignments allow only one axis to be ganged or auto squared.
// A axis pin numbers are used for the ganged/auto squared axis.
// If a second axis is to be ganged/auto squared pin assignments needs to be changed!
@@ -113,6 +117,6 @@
#if EEPROM_ENABLE || KEYPAD_ENABLE
#define I2C_PORT 4
-#define I2C_SCL4 (24u) // Not used, for info only
-#define I2C_SDA4 (25u) // Not used, for info only
+#define I2C_SCL4 (24u) // Not referenced, for info only
+#define I2C_SDA4 (25u) // Not referenced, for info only
#endif
diff --git a/grblHAL_Teensy4/src/T41U5XBB.c b/grblHAL_Teensy4/src/T41U5XBB.c
index b85d35f..9543b53 100644
--- a/grblHAL_Teensy4/src/T41U5XBB.c
+++ b/grblHAL_Teensy4/src/T41U5XBB.c
@@ -23,7 +23,7 @@
#include "driver.h"
-#ifdef BOARD_T41U5XBB
+#if defined(BOARD_T41U5XBB) || defined(BOARD_T41U5XBB_SS)
//#include "Arduino.h"
#include
@@ -31,32 +31,20 @@
#include "grbl/protocol.h"
-static gpio_t stx[AUX_N_IN];
+static input_signal_t *stx;
static gpio_t aux_out[AUX_N_OUT];
static void aux_settings_load (void);
static status_code_t aux_set_invert_out (setting_id_t id, uint_fast16_t int_value);
static uint32_t aux_get_invert_out (setting_id_t setting);
-
-static input_signal_t aux_in[] = {
- { .id = Input_Aux0, .port = &stx[0], .pin = AUXINPUT0_PIN, .group = 0 }
-#if AUX_N_IN == 4
- , { .id = Input_Aux1, .port = &stx[1], .pin = AUXINPUT1_PIN, .group = 0 },
- { .id = Input_Aux2, .port = &stx[2], .pin = AUXINPUT2_PIN, .group = 0 },
- { .id = Input_Aux3, .port = &stx[3], .pin = AUXINPUT3_PIN, .group = 0 }
-#endif
-};
+static char input_ports[30]; //
static const setting_group_detail_t aux_groups[] = {
{ Group_Root, Group_AuxPorts, "Aux ports"}
};
static const setting_detail_t aux_settings[] = {
-#if AUX_N_IN == 4
- { Settings_IoPort_InvertIn, Group_AuxPorts, "Invert I/O Port inputs", NULL, Format_Bitfield, "Port 0,Port 1,Port 2,Port 3", NULL, NULL, Setting_NonCore, &settings.ioport.invert_in.mask },
-#else
- { Settings_IoPort_InvertIn, Group_AuxPorts, "Invert I/O Port inputs", NULL, Format_Bitfield, "Port 0", NULL, NULL, Setting_NonCore, &settings.ioport.invert_in.mask },
-#endif
+ { Settings_IoPort_InvertIn, Group_AuxPorts, "Invert I/O Port inputs", NULL, Format_Bitfield, input_ports, NULL, NULL, Setting_NonCore, &settings.ioport.invert_in.mask },
{ Settings_IoPort_InvertOut, Group_AuxPorts, "Invert I/O Port outputs", NULL, Format_Bitfield, "Port 0,Port 1,Port 2", NULL, NULL, Setting_NonCoreFn, aux_set_invert_out, aux_get_invert_out },
};
@@ -142,8 +130,8 @@ static int32_t wait_on_input (bool digital, uint8_t port, wait_mode_t wait_mode,
int32_t value = -1;
if(digital) {
- if(port < AUX_N_IN)
- value = get_input(aux_in[port].port, (settings.ioport.invert_in.mask << port) & 0x01, wait_mode, timeout);
+ if(port < hal.port.num_digital_in)
+ value = get_input(stx[port].port, (settings.ioport.invert_in.mask << port) & 0x01, wait_mode, timeout);
}
// else if(port == 0)
// value = analogRead(41);
@@ -157,32 +145,25 @@ static int32_t wait_on_input (bool digital, uint8_t port, wait_mode_t wait_mode,
return value;
}
-void board_init (void)
+void board_init (pin_group_pins_t *aux_inputs)
{
+ stx = aux_inputs->pins;
+
hal.port.digital_out = digital_out;
hal.port.wait_on_input = wait_on_input;
// hal.port.num_analog_in = 1;
- hal.port.num_digital_in = AUX_N_IN;
+ hal.port.num_digital_in = aux_inputs->n_pins;
hal.port.num_digital_out = AUX_N_OUT;
details.on_get_settings = grbl.on_get_settings;
grbl.on_get_settings = on_get_settings;
- bool pullup;
- uint32_t i = AUX_N_IN;
- input_signal_t *signal;
- do {
- pullup = true; //??
- signal = &aux_in[--i];
- signal->irq_mode = IRQ_Mode_None;
+ uint32_t i;
- pinMode(signal->pin, pullup ? INPUT_PULLUP : INPUT_PULLDOWN);
- signal->gpio.reg = (gpio_reg_t *)digital_pin_to_info_PGM[signal->pin].reg;
- signal->gpio.bit = digital_pin_to_info_PGM[signal->pin].mask;
-
- if(signal->port != NULL)
- memcpy(signal->port, &signal->gpio, sizeof(gpio_t));
- } while(i);
+ for(i = 0; i < hal.port.num_digital_in; i++) {
+ strcat(input_ports, i == 0 ? "Port " : ",Port ");
+ strcat(input_ports, uitoa(i));
+ }
pinModeOutput(&aux_out[0], AUXOUTPUT0_PIN);
pinModeOutput(&aux_out[1], AUXOUTPUT1_PIN);
diff --git a/grblHAL_Teensy4/src/T41U5XBB_map.h b/grblHAL_Teensy4/src/T41U5XBB_map.h
index d17b420..0bba8c0 100644
--- a/grblHAL_Teensy4/src/T41U5XBB_map.h
+++ b/grblHAL_Teensy4/src/T41U5XBB_map.h
@@ -5,7 +5,7 @@
Board by Phil Barrett: https://github.com/phil-barrett/grblHAL-teensy-4.x
- Copyright (c) 2020 Terje Io
+ Copyright (c) 2020-2021 Terje Io
Grbl is free software: you can redistribute it and/or modify
it under the terms of the GNU General Public License as published by
@@ -24,12 +24,14 @@
#define BOARD_NAME "T41U5XBB"
#define HAS_BOARD_INIT
-void board_init (void);
-
#if N_AXIS > 5
#error Max number of axes is 5 for T41U5XBB
#endif
+#if SPINDLE_SYNC_ENABLE
+#error Spindle sync is not supported for T41U5XBB
+#endif
+
// Default pin assignments allow only one axis to be ganged or auto squared.
// B axis pin numbers are used for the ganged/auto squared axis.
// If a second axis is to be ganged/auto squared pin assignments needs to be changed!
@@ -37,7 +39,7 @@ void board_init (void);
#define X_GANGED 0
#define X_AUTO_SQUARE 0
#define Y_GANGED 0
-#define Y_AUTO_SQUARE 0
+#define Y_AUTO_SQUARE 1
#define Z_GANGED 0
#define Z_AUTO_SQUARE 0
//
@@ -61,12 +63,13 @@ void board_init (void);
#define Y_ENABLE_PIN (40u)
#define Y_LIMIT_PIN (21u)
+// Changed to use A pins rather than B pins
#if Y_GANGED || Y_AUTO_SQUARE
-#define Y2_STEP_PIN (26u)
-#define Y2_DIRECTION_PIN (27u)
-#define Y2_ENABLE_PIN (37u)
+#define Y2_STEP_PIN (8u)
+#define Y2_DIRECTION_PIN (9u)
+#define Y2_ENABLE_PIN (38u)
#if Y_AUTO_SQUARE
- #define Y2_LIMIT_PIN (28u)
+ #define Y2_LIMIT_PIN (23u)
#endif
#endif
@@ -112,7 +115,13 @@ void board_init (void);
#define SAFETY_DOOR_PIN (29u)
// Define probe switch input pin.
-#define PROBE_PIN (15U)
+#define PROBE_PIN (15u)
+
+#if QEI_ENABLE
+#define QEI_A_PIN (30u) // ST1
+#define QEI_B_PIN (34u) // ST2
+#define QEI_SELECT_PIN (35u) // ST3
+#endif
// Define auxillary input pins
#define AUXINPUT0_PIN (36u) // ST0
@@ -120,11 +129,6 @@ void board_init (void);
#define AUXINPUT1_PIN (30u) // ST1
#define AUXINPUT2_PIN (34u) // ST2
#define AUXINPUT3_PIN (35u) // ST3
-#define AUX_N_IN 4
-#define AUX_IN_MASK 0b1111
-#else
-#define AUX_N_IN 1
-#define AUX_IN_MASK 0b1
#endif
#define AUXOUTPUT0_PIN (31u) // AUX0
@@ -139,12 +143,6 @@ void board_init (void);
#if EEPROM_ENABLE || KEYPAD_ENABLE
#define I2C_PORT 4
-#define I2C_SCL4 (24u) // Not used, for info only
-#define I2C_SDA4 (25u) // Not used, for info only
-#endif
-
-#if QEI_ENABLE
-#define QEI_A_PIN (30u) // ST1
-#define QEI_B_PIN (34u) // ST2
-#define QEI_SELECT_PIN (35u) // ST3
+#define I2C_SCL4 (24u) // Not referenced, for info only
+#define I2C_SDA4 (25u) // Not referenced, for info only
#endif
diff --git a/grblHAL_Teensy4/src/T41U5XBB_ss_map.h b/grblHAL_Teensy4/src/T41U5XBB_ss_map.h
new file mode 100644
index 0000000..1cb4fe8
--- /dev/null
+++ b/grblHAL_Teensy4/src/T41U5XBB_ss_map.h
@@ -0,0 +1,157 @@
+/*
+ T41U5XBB_ss_map.h - driver code for IMXRT1062 processor (on Teensy 4.1 board)
+
+ Part of grblHAL
+
+ !!IMPORTANT!! This map is for a modified board, see https://github.com/terjeio/grblHAL/discussions/289 for details.
+
+ Board by Phil Barrett: https://github.com/phil-barrett/grblHAL-teensy-4.x
+
+ Copyright (c) 2020-2021 Terje Io
+
+ Grbl is free software: you can redistribute it and/or modify
+ it under the terms of the GNU General Public License as published by
+ the Free Software Foundation, either version 3 of the License, or
+ (at your option) any later version.
+
+ Grbl is distributed in the hope that it will be useful,
+ but WITHOUT ANY WARRANTY; without even the implied warranty of
+ MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ GNU General Public License for more details.
+
+ You should have received a copy of the GNU General Public License
+ along with Grbl. If not, see .
+*/
+
+#define BOARD_NAME "T41U5XBB"
+#define HAS_BOARD_INIT
+
+#if N_AXIS > 5
+#error Max number of axes is 5 for T41U5XBB
+#endif
+
+#if QEI_ENABLE && SPINDLE_SYNC_ENABLE
+#error Quadrature encoder and spindle sync cannot be enabled at the same time
+#endif
+
+// Default pin assignments allow only one axis to be ganged or auto squared.
+// B axis pin numbers are used for the ganged/auto squared axis.
+// If a second axis is to be ganged/auto squared pin assignments needs to be changed!
+// Set to 1 to enable, 0 to disable.
+#define X_GANGED 0
+#define X_AUTO_SQUARE 0
+#define Y_GANGED 0
+#define Y_AUTO_SQUARE 1
+#define Z_GANGED 0
+#define Z_AUTO_SQUARE 0
+//
+
+#define X_STEP_PIN (2u)
+#define X_DIRECTION_PIN (3u)
+#define X_ENABLE_PIN (10u)
+#define X_LIMIT_PIN (20u)
+
+#if X_GANGED || X_AUTO_SQUARE
+#define X2_STEP_PIN (26u)
+#define X2_DIRECTION_PIN (27u)
+#define X2_ENABLE_PIN (37u)
+#if X_AUTO_SQUARE
+ #define X2_LIMIT_PIN (28u)
+#endif
+#endif
+
+#define Y_STEP_PIN (4u)
+#define Y_DIRECTION_PIN (5u)
+#define Y_ENABLE_PIN (40u)
+#define Y_LIMIT_PIN (21u)
+
+// Changed to use A pins rather than B pins
+#if Y_GANGED || Y_AUTO_SQUARE
+#define Y2_STEP_PIN (8u)
+#define Y2_DIRECTION_PIN (9u)
+#define Y2_ENABLE_PIN (38u)
+#if Y_AUTO_SQUARE
+ #define Y2_LIMIT_PIN (23u)
+#endif
+#endif
+
+#define Z_STEP_PIN (6u)
+#define Z_DIRECTION_PIN (7u)
+#define Z_ENABLE_PIN (39u)
+#define Z_LIMIT_PIN (22u)
+
+#if Z_GANGED || Z_AUTO_SQUARE
+#define Z2_STEP_PIN (26u)
+#define Z2_DIRECTION_PIN (27u)
+#define Z2_ENABLE_PIN (37u)
+#define Z2_LIMIT_PIN (28u)
+#endif
+
+#if N_AXIS > 3
+#define A_STEP_PIN (8u)
+#define A_DIRECTION_PIN (9u)
+#define A_ENABLE_PIN (38u)
+#define A_LIMIT_PIN (23u)
+#endif
+
+#if N_AXIS > 4
+#define B_STEP_PIN (26u)
+#define B_DIRECTION_PIN (27u)
+#define B_ENABLE_PIN (37u)
+#define B_LIMIT_PIN (28u)
+#endif
+
+// Define spindle enable and spindle direction output pins.
+#define SPINDLE_ENABLE_PIN (12u)
+#define SPINDLE_DIRECTION_PIN (11u)
+#define SPINDLEPWMPIN (13u) // NOTE: only pin 12 or pin 13 can be assigned!
+
+// Define flood and mist coolant enable output pins.
+#define COOLANT_FLOOD_PIN (19u)
+#define COOLANT_MIST_PIN (18u)
+
+// Define user-control CONTROLs (cycle start, reset, feed hold, door) input pins.
+#define RESET_PIN (35u)
+#define FEED_HOLD_PIN (16u)
+#define CYCLE_START_PIN (17u)
+#define SAFETY_DOOR_PIN (29u)
+
+// Define probe switch input pin.
+#define PROBE_PIN (15u)
+
+#if QEI_ENABLE
+#define QEI_A_PIN (30u) // ST1
+#define QEI_B_PIN (34u) // ST2
+#define QEI_SELECT_PIN (35u) // ST3
+#endif
+
+#if SPINDLE_SYNC_ENABLE
+#define SPINDLE_INDEX_PIN (34u) // ST2
+#define SPINDLE_PULSE_PIN (14u) // ST3
+#endif
+
+// Define auxillary input pins
+#define AUXINPUT0_PIN (36u) // ST0
+#if !QEI_ENABLE
+#define AUXINPUT1_PIN (30u) // ST1
+#if !SPINDLE_SYNC_ENABLE
+#define AUXINPUT2_PIN (34u) // ST2
+#define AUXINPUT3_PIN (14u) // ST3
+#endif
+#endif
+
+#define AUXOUTPUT0_PIN (31u) // AUX0
+#define AUXOUTPUT1_PIN (32u) // AUX1
+#define AUXOUTPUT2_PIN (33u) // AUX2
+#define AUX_N_OUT 3
+#define AUX_OUT_MASK 0b111
+
+#if KEYPAD_ENABLE
+#define KEYPAD_STROBE_PIN (41u) // I2C ST
+#endif
+
+#if EEPROM_ENABLE || KEYPAD_ENABLE
+#define I2C_PORT 4
+#define I2C_SCL4 (24u) // Not referenced, for info only
+#define I2C_SDA4 (25u) // Not referenced, for info only
+#endif
diff --git a/grblHAL_Teensy4/src/cnc_boosterpack_map.h b/grblHAL_Teensy4/src/cnc_boosterpack_map.h
index 6fe12eb..c94254a 100644
--- a/grblHAL_Teensy4/src/cnc_boosterpack_map.h
+++ b/grblHAL_Teensy4/src/cnc_boosterpack_map.h
@@ -3,7 +3,7 @@
Part of grblHAL
- Copyright (c) 2020 Terje Io
+ Copyright (c) 2020-2021 Terje Io
Grbl is free software: you can redistribute it and/or modify
it under the terms of the GNU General Public License as published by
@@ -25,6 +25,10 @@
#error Max number of axes is 3 for CNC BoosterPack
#endif
+#if SPINDLE_SYNC_ENABLE
+#error Spindle sync is not supported for CNC BoosterPack
+#endif
+
#ifdef EEPROM_ENABLE
#undef EEPROM_ENABLE
#endif
@@ -73,13 +77,13 @@
#if EEPROM_ENABLE || KEYPAD_ENABLE
#define I2C_PORT 0
-#define I2C_SCL0 (19u) // Not used, for info only
-#define I2C_SDA0 (18u) // Not used, for info only
+#define I2C_SCL0 (19u) // Not referenced, for info only
+#define I2C_SDA0 (18u) // Not referenced, for info only
#endif
#define UART_PORT 5
-#define UART_RX5 (21u) // Not used, for info only
-#define UART_TX5 (20u) // Not used, for info only
+#define UART_RX5 (21u) // Not referenced, for info only
+#define UART_TX5 (20u) // Not referenced, for info only
#define GPIO0_PIN (3u)
#define GPIO1_PIN (29u)
diff --git a/grblHAL_Teensy4/src/driver.c b/grblHAL_Teensy4/src/driver.c
index 0273387..147fb6b 100644
--- a/grblHAL_Teensy4/src/driver.c
+++ b/grblHAL_Teensy4/src/driver.c
@@ -104,15 +104,6 @@ static void ppi_timeout_isr (void);
#endif
#endif
-#define INPUT_GROUP_CONTROL (1 << 0)
-#define INPUT_GROUP_PROBE (1 << 1)
-#define INPUT_GROUP_LIMIT (1 << 2)
-#define INPUT_GROUP_KEYPAD (1 << 3)
-#define INPUT_GROUP_MPG (1 << 4)
-#define INPUT_GROUP_QEI (1 << 5)
-#define INPUT_GROUP_QEI_SELECT (1 << 6)
-#define INPUT_GROUP_SPINDLE_INDEX (1 << 7)
-
typedef struct {
volatile uint_fast8_t head;
volatile uint_fast8_t tail;
@@ -259,63 +250,93 @@ static gpio_t QEI_A, QEI_B;
static gpio_t SpindleIndex;
#endif
-static input_signal_t inputpin[] = {
-#if ESTOP_ENABLE
- { .id = Input_EStop, .port = &Reset, .pin = RESET_PIN, .group = INPUT_GROUP_CONTROL },
-#else
- { .id = Input_Reset, .port = &Reset, .pin = RESET_PIN, .group = INPUT_GROUP_CONTROL },
+#ifdef AUXINPUT0_PIN
+ static gpio_t AuxIn0;
#endif
- { .id = Input_FeedHold, .port = &FeedHold, .pin = FEED_HOLD_PIN, .group = INPUT_GROUP_CONTROL },
- { .id = Input_CycleStart, .port = &CycleStart, .pin = CYCLE_START_PIN, .group = INPUT_GROUP_CONTROL },
+#ifdef AUXINPUT1_PIN
+ static gpio_t AuxIn1;
+#endif
+#ifdef AUXINPUT2_PIN
+ static gpio_t AuxIn2;
+#endif
+#ifdef AUXINPUT3_PIN
+ static gpio_t AuxIn3;
+#endif
+
+input_signal_t inputpin[] = {
+#if ESTOP_ENABLE
+ { .id = Input_EStop, .port = &Reset, .pin = RESET_PIN, .group = PinGroup_Control },
+#else
+ { .id = Input_Reset, .port = &Reset, .pin = RESET_PIN, .group = PinGroup_Control },
+#endif
+ { .id = Input_FeedHold, .port = &FeedHold, .pin = FEED_HOLD_PIN, .group = PinGroup_Control },
+ { .id = Input_CycleStart, .port = &CycleStart, .pin = CYCLE_START_PIN, .group = PinGroup_Control },
#if SAFETY_DOOR_ENABLE
- { .id = Input_SafetyDoor, .port = &SafetyDoor, .pin = SAFETY_DOOR_PIN, .group = INPUT_GROUP_CONTROL },
+ { .id = Input_SafetyDoor, .port = &SafetyDoor, .pin = SAFETY_DOOR_PIN, .group = PinGroup_Control },
#endif
#if defined(LIMITS_OVERRIDE_PIN)
- { .id = Input_LimitsOverride, .port = &LimitsOverride, .pin = LIMITS_OVERRIDE_PIN, .group = INPUT_GROUP_CONTROL },
+ { .id = Input_LimitsOverride, .port = &LimitsOverride, .pin = LIMITS_OVERRIDE_PIN, .group = PinGroup_Control },
#endif
- { .id = Input_Probe, .port = &Probe, .pin = PROBE_PIN, .group = INPUT_GROUP_PROBE },
- { .id = Input_LimitX, .port = &LimitX, .pin = X_LIMIT_PIN, .group = INPUT_GROUP_LIMIT },
+ { .id = Input_Probe, .port = &Probe, .pin = PROBE_PIN, .group = PinGroup_Probe },
+// Limit input pins must be consecutive
+ { .id = Input_LimitX, .port = &LimitX, .pin = X_LIMIT_PIN, .group = PinGroup_Limit },
#ifdef X2_LIMIT_PIN
- { .id = Input_LimitX_Max, .port = &LimitX2, .pin = X2_LIMIT_PIN, .group = INPUT_GROUP_LIMIT },
+ { .id = Input_LimitX_Max, .port = &LimitX2, .pin = X2_LIMIT_PIN, .group = PinGroup_Limit },
#endif
- { .id = Input_LimitY, .port = &LimitY, .pin = Y_LIMIT_PIN, .group = INPUT_GROUP_LIMIT },
+ { .id = Input_LimitY, .port = &LimitY, .pin = Y_LIMIT_PIN, .group = PinGroup_Limit },
#ifdef Y2_LIMIT_PIN
- { .id = Input_LimitY_Max, .port = &LimitY2, .pin = Y2_LIMIT_PIN, .group = INPUT_GROUP_LIMIT },
+ { .id = Input_LimitY_Max, .port = &LimitY2, .pin = Y2_LIMIT_PIN, .group = PinGroup_Limit },
#endif
- { .id = Input_LimitZ, .port = &LimitZ, .pin = Z_LIMIT_PIN, .group = INPUT_GROUP_LIMIT }
+ { .id = Input_LimitZ, .port = &LimitZ, .pin = Z_LIMIT_PIN, .group = PinGroup_Limit }
#ifdef Z2_LIMIT_PIN
- , { .id = Input_LimitZ_Max, .port = &LimitZ2, .pin = Z2_LIMIT_PIN, .group = INPUT_GROUP_LIMIT }
+ , { .id = Input_LimitZ_Max, .port = &LimitZ2, .pin = Z2_LIMIT_PIN, .group = PinGroup_Limit }
#endif
#ifdef A_LIMIT_PIN
- , { .id = Input_LimitA, .port = &LimitA, .pin = A_LIMIT_PIN, .group = INPUT_GROUP_LIMIT }
+ , { .id = Input_LimitA, .port = &LimitA, .pin = A_LIMIT_PIN, .group = PinGroup_Limit }
#endif
#ifdef B_LIMIT_PIN
- , { .id = Input_LimitB, .port = &LimitB, .pin = B_LIMIT_PIN, .group = INPUT_GROUP_LIMIT }
+ , { .id = Input_LimitB, .port = &LimitB, .pin = B_LIMIT_PIN, .group = PinGroup_Limit }
#endif
#ifdef C_LIMIT_PIN
- , { .id = Input_LimitC, .port = &LimitC, .pin = C_LIMIT_PIN, .group = INPUT_GROUP_LIMIT }
+ , { .id = Input_LimitC, .port = &LimitC, .pin = C_LIMIT_PIN, .group = PinGroup_Limit }
#endif
+// End limit pin definitions
#if MPG_MODE_ENABLE
- , { .id = Input_ModeSelect, .port = &ModeSelect, .pin = MODE_PIN, .group = INPUT_GROUP_MPG }
+ , { .id = Input_ModeSelect, .port = &ModeSelect, .pin = MODE_PIN, .group = PinGroup_MPG }
#endif
#if KEYPAD_ENABLE && defined(KEYPAD_STROBE_PIN)
- , { .id = Input_KeypadStrobe, .port = &KeypadStrobe, .pin = KEYPAD_STROBE_PIN, .group = INPUT_GROUP_KEYPAD }
+ , { .id = Input_KeypadStrobe, .port = &KeypadStrobe, .pin = KEYPAD_STROBE_PIN, .group = PinGroup_Keypad }
#endif
#ifdef SPINDLE_INDEX_PIN
- , { .id = Input_SpindleIndex, .port = &SpindleIndex, .pin = SPINDLE_INDEX_PIN, .group = INPUT_GROUP_SPINDLE_INDEX }
+ , { .id = Input_SpindleIndex, .port = &SpindleIndex, .pin = SPINDLE_INDEX_PIN, .group = PinGroup_SpindleIndex }
#endif
#if QEI_ENABLE
- , { .id = Input_QEI_A, .port = &QEI_A, .pin = QEI_A_PIN, .group = INPUT_GROUP_QEI }
- , { .id = Input_QEI_B, .port = &QEI_B, .pin = QEI_B_PIN, .group = INPUT_GROUP_QEI }
+ , { .id = Input_QEI_A, .port = &QEI_A, .pin = QEI_A_PIN, .group = PinGroup_QEI }
+ , { .id = Input_QEI_B, .port = &QEI_B, .pin = QEI_B_PIN, .group = PinGroup_QEI }
#if QEI_SELECT_ENABLED
- , { .id = Input_QEI_Select, .port = &QEI_Select, .pin = QEI_SELECT_PIN, .group = INPUT_GROUP_QEI_SELECT }
+ , { .id = Input_QEI_Select, .port = &QEI_Select, .pin = QEI_SELECT_PIN, .group = PinGroup_QEI_Select }
#endif
#if QEI_INDEX_ENABLED
- , { .id = Input_QEI_Index, .port = &QEI_Index, .pin = QEI_INDEX_PIN, .group = INPUT_GROUP_QEI }
+ , { .id = Input_QEI_Index, .port = &QEI_Index, .pin = QEI_INDEX_PIN, .group = PinGroup_QEI }
#endif
#endif
+// Aux input pins must be consecutive
+#ifdef AUXINPUT0_PIN
+ , { .id = Input_Aux0, .port = &AuxIn0, .pin = AUXINPUT0_PIN, .group = PinGroup_AuxInput }
+#endif
+#ifdef AUXINPUT1_PIN
+ , { .id = Input_Aux1, .port = &AuxIn1, .pin = AUXINPUT1_PIN, .group = PinGroup_AuxInput }
+#endif
+#ifdef AUXINPUT2_PIN
+ , { .id = Input_Aux2, .port = &AuxIn2, .pin = AUXINPUT2_PIN, .group = PinGroup_AuxInput }
+#endif
+#ifdef AUXINPUT3_PIN
+ , { .id = Input_Aux3, .port = &AuxIn3, .pin = AUXINPUT3_PIN, .group = PinGroup_AuxInput }
+#endif
};
+static pin_group_pins_t aux_inputs = {0}, limit_inputs = {0};
+
#if USB_SERIAL_CDC || QEI_ENABLE
#define ADD_MSEVENT 1
static volatile bool ms_event = false;
@@ -344,7 +365,7 @@ static void spindle_set_speed (uint_fast16_t pwm_value);
static modbus_stream_t modbus_stream = {0};
#endif
-#ifdef SPINDLE_SYNC_ENABLE
+#if SPINDLE_SYNC_ENABLE
#include "grbl/spindle_sync.h"
@@ -698,7 +719,7 @@ static void stepperCyclesPerTick (uint32_t cycles_per_tick)
// stepper_t struct is defined in grbl/stepper.h
static void stepperPulseStart (stepper_t *stepper)
{
-#ifdef SPINDLE_SYNC_ENABLE
+#if SPINDLE_SYNC_ENABLE
if(stepper->new_block && stepper->exec_segment->spindle_sync) {
spindle_tracker.stepper_pulse_start_normal = hal.stepper.pulse_start;
hal.stepper.pulse_start = stepperPulseStartSynchronized;
@@ -723,7 +744,7 @@ static void stepperPulseStart (stepper_t *stepper)
// stepper_t struct is defined in grbl/stepper.h
static void stepperPulseStartDelayed (stepper_t *stepper)
{
-#ifdef SPINDLE_SYNC_ENABLE
+#if SPINDLE_SYNC_ENABLE
if(stepper->new_block && stepper->exec_segment->spindle_sync) {
spindle_tracker.stepper_pulse_start_normal = hal.stepper.pulse_start;
hal.stepper.pulse_start = stepperPulseStartSynchronized;
@@ -755,7 +776,7 @@ static void stepperPulseStartDelayed (stepper_t *stepper)
}
}
-#ifdef SPINDLE_SYNC_ENABLE
+#if SPINDLE_SYNC_ENABLE
// Spindle sync version: sets stepper direction and pulse pins and starts a step pulse.
// Switches back to "normal" version if spindle synchronized motion is finished.
@@ -975,18 +996,17 @@ static void StepperDisableMotors (axes_signals_t axes, squaring_mode_t mode)
// stepper drivers for sensorless homing.
static void limitsEnable (bool on, bool homing)
{
- uint32_t i = sizeof(inputpin) / sizeof(input_signal_t);
+ uint32_t i = limit_inputs.n_pins;
on &= settings.limits.flags.hard_enabled;
do {
- if(inputpin[--i].group == INPUT_GROUP_LIMIT) {
- inputpin[i].gpio.reg->ISR = inputpin[i].gpio.bit; // Clear interrupt.
- if(on)
- inputpin[i].gpio.reg->IMR |= inputpin[i].gpio.bit; // Enable interrupt.
- else
- inputpin[i].gpio.reg->IMR &= ~inputpin[i].gpio.bit; // Disable interrupt.
- }
+ i--;
+ limit_inputs.pins[i].gpio.reg->ISR = limit_inputs.pins[i].gpio.bit; // Clear interrupt.
+ if(on)
+ limit_inputs.pins[i].gpio.reg->IMR |= limit_inputs.pins[i].gpio.bit; // Enable interrupt.
+ else
+ limit_inputs.pins[i].gpio.reg->IMR &= ~limit_inputs.pins[i].gpio.bit; // Disable interrupt.
} while(i);
}
@@ -1055,7 +1075,7 @@ inline static void spindle_off ()
inline static void spindle_on ()
{
DIGITAL_OUT(spindleEnable, !settings.spindle.invert.on);
-#ifdef SPINDLE_SYNC_ENABLE
+#if SPINDLE_SYNC_ENABLE
spindleDataReset();
#endif
}
@@ -1155,7 +1175,7 @@ static void spindleSetStateVariable (spindle_state_t state, float rpm)
spindle_set_speed(spindle_compute_pwm_value(&spindle_pwm, rpm, false));
}
-#ifdef SPINDLE_SYNC_ENABLE
+#if SPINDLE_SYNC_ENABLE
if(settings.spindle.at_speed_tolerance > 0.0f) {
float tolerance = rpm * settings.spindle.at_speed_tolerance / 100.0f;
spindle_data.rpm_low_limit = rpm - tolerance;
@@ -1181,7 +1201,7 @@ static spindle_state_t spindleGetState (void)
if(pwmEnabled)
state.on |= pwmEnabled;
-#ifdef SPINDLE_SYNC_ENABLE
+#if SPINDLE_SYNC_ENABLE
float rpm = spindleGetData(SpindleData_RPM)->rpm;
state.at_speed = settings.spindle.at_speed_tolerance <= 0.0f || (rpm >= spindle_data.rpm_low_limit && rpm <= spindle_data.rpm_high_limit);
#endif
@@ -1206,7 +1226,7 @@ static void spindlePulseOn (uint_fast16_t pulse_length)
#endif
-#ifdef SPINDLE_SYNC_ENABLE
+#if SPINDLE_SYNC_ENABLE
static spindle_data_t *spindleGetData (spindle_data_request_t request)
{
@@ -1397,7 +1417,7 @@ static void settings_changed (settings_t *settings)
hal.spindle.set_state = spindleSetState;
#endif
-#ifdef SPINDLE_SYNC_ENABLE
+#if SPINDLE_SYNC_ENABLE
if((hal.spindle.get_data = settings->spindle.ppr > 0 ? spindleGetData : NULL) && spindle_encoder.ppr != settings->spindle.ppr) {
@@ -1630,7 +1650,7 @@ static void settings_changed (settings_t *settings)
signal->gpio.reg->ISR = signal->gpio.bit; // Clear interrupt.
- if(signal->group != INPUT_GROUP_LIMIT) // If pin is not a limit pin
+ if(signal->group != PinGroup_Limit) // If pin is not a limit pin
signal->gpio.reg->IMR |= signal->gpio.bit; // enable interrupt
signal->active = (signal->gpio.reg->DR & signal->gpio.bit) != 0;
@@ -1877,7 +1897,7 @@ static bool driver_setup (settings_t *settings)
*(portConfigRegister(SPINDLEPWMPIN)) = 1;
-#ifdef SPINDLE_SYNC_ENABLE
+#if SPINDLE_SYNC_ENABLE
CCM_CCGR1 |= CCM_CCGR1_GPT1_BUS(CCM_CCGR_ON);
CCM_CMEOR |= CCM_CMEOR_MOD_EN_OV_GPT;
@@ -2078,7 +2098,7 @@ bool driver_init (void)
options[strlen(options) - 1] = '\0';
hal.info = "iMXRT1062";
- hal.driver_version = "210313";
+ hal.driver_version = "210414";
#ifdef BOARD_NAME
hal.board = BOARD_NAME;
#endif
@@ -2122,7 +2142,7 @@ bool driver_init (void)
hal.spindle.pulse_on = spindlePulseOn;
#endif
#endif
-#ifdef SPINDLE_SYNC_ENABLE
+#if SPINDLE_SYNC_ENABLE
hal.driver_cap.spindle_sync = On;
hal.driver_cap.spindle_at_speed = On;
#endif
@@ -2226,8 +2246,27 @@ bool driver_init (void)
uart_debug_write(ASCII_EOL "UART Debug:" ASCII_EOL);
#endif
+ uint32_t i;
+ input_signal_t *signal;
+
+ for(i = 0 ; i < sizeof(inputpin) / sizeof(input_signal_t); i++) {
+ signal = &inputpin[i];
+
+ if(signal->group == PinGroup_AuxInput) {
+ if(aux_inputs.pins == NULL)
+ aux_inputs.pins = signal;
+ aux_inputs.n_pins++;
+ }
+
+ if(signal->group == PinGroup_Limit) {
+ if(limit_inputs.pins == NULL)
+ limit_inputs.pins = signal;
+ limit_inputs.n_pins++;
+ }
+ }
+
#ifdef HAS_BOARD_INIT
- board_init();
+ board_init(&aux_inputs);
#endif
#if ETHERNET_ENABLE
@@ -2298,7 +2337,7 @@ static void stepper_pulse_isr_delayed (void)
TMR4_CTRL0 |= TMR_CTRL_CM(0b001);
}
-#if defined(SPINDLE_SYNC_ENABLE) && SPINDLE_PULSE_PIN == 14
+#if SPINDLE_SYNC_ENABLE && SPINDLE_PULSE_PIN == 14
static void spindle_pulse_isr (void)
{
@@ -2386,15 +2425,15 @@ static void debounce_isr (void)
grp |= signal->group;
}
- if(grp & INPUT_GROUP_LIMIT)
+ if(grp & PinGroup_Limit)
hal.limits.interrupt_callback(limitsGetState());
- if(grp & INPUT_GROUP_CONTROL)
+ if(grp & PinGroup_Control)
hal.control.interrupt_callback(systemGetState());
#if QEI_SELECT_ENABLED
- if(grp & INPUT_GROUP_QEI_SELECT) {
+ if(grp & PinGroup_QEI_Select) {
if(!qei.dbl_click_timeout)
qei.dbl_click_timeout = qei.encoder.settings->dbl_click_window;
else if(qei.dbl_click_timeout < qei.encoder.settings->dbl_click_window - 40) {
@@ -2437,7 +2476,7 @@ static void gpio_isr (void)
debounce = true;
} else {
#if QEI_ENABLE
- if(inputpin[i].group & INPUT_GROUP_QEI) {
+ if(inputpin[i].group & PinGroup_QEI) {
qei_update();
/*
QEI_A.reg->IMR &= ~QEI_A.bit; // Switch off
@@ -2450,8 +2489,8 @@ static void gpio_isr (void)
} else
#endif
-#if defined(SPINDLE_SYNC_ENABLE) && defined(SPINDLE_INDEX_PIN)
- if(inputpin[i].group & INPUT_GROUP_SPINDLE_INDEX) {
+#if SPINDLE_SYNC_ENABLE && defined(SPINDLE_INDEX_PIN)
+ if(inputpin[i].group & PinGroup_SpindleIndex) {
spindleLock = true;
spindle_encoder.counter.index_count++;
spindle_encoder.counter.last_index = GPT2_CNT;
@@ -2469,18 +2508,18 @@ static void gpio_isr (void)
TMR3_CTRL0 |= TMR_CTRL_CM(0b001);
}
- if(grp & INPUT_GROUP_LIMIT) {
+ if(grp & PinGroup_Limit) {
limit_signals_t state = limitsGetState();
if(limit_signals_merge(state).value) //TODO: add check for limit switches having same state as when limit_isr were invoked?
hal.limits.interrupt_callback(state);
}
- if(grp & INPUT_GROUP_CONTROL)
+ if(grp & PinGroup_Control)
hal.control.interrupt_callback(systemGetState());
#if QEI_SELECT_ENABLED
- if(grp & INPUT_GROUP_QEI_SELECT) {
+ if(grp & PinGroup_QEI_Select) {
if(!qei.dbl_click_timeout)
qei.dbl_click_timeout = qei.encoder.settings->dbl_click_window;
else if(qei.dbl_click_timeout < qei.encoder.settings->dbl_click_window - 40) {
@@ -2496,7 +2535,7 @@ static void gpio_isr (void)
static bool mpg_mutex = false;
- if((grp & INPUT_GROUP_MPG) && !mpg_mutex) {
+ if((grp & PinGroup_MPG) && !mpg_mutex) {
mpg_mutex = true;
modeChange();
// hal.delay_ms(50, modeChange);
@@ -2505,7 +2544,7 @@ static void gpio_isr (void)
#endif
#if KEYPAD_ENABLE
- if(grp & INPUT_GROUP_KEYPAD)
+ if(grp & PinGroup_Keypad)
keypad_keyclick_handler(!(KeypadStrobe.reg->DR & KeypadStrobe.bit));
#endif
}
diff --git a/grblHAL_Teensy4/src/driver.h b/grblHAL_Teensy4/src/driver.h
index 8a9641f..9ea8cbe 100644
--- a/grblHAL_Teensy4/src/driver.h
+++ b/grblHAL_Teensy4/src/driver.h
@@ -1,5 +1,5 @@
/*
- driver.h - driver code for IMXRT1062 processor (on Teensy 4.0 board)
+ driver.h - driver code for IMXRT1062 processor (on Teensy 4.x board)
Part of grblHAL
@@ -36,7 +36,7 @@
#include "grbl/hal.h"
#include "grbl/nuts_bolts.h"
-
+#include "grbl/crossbar.h"
#define DIGITAL_IN(gpio) (!!(gpio.reg->DR & gpio.bit))
#define DIGITAL_OUT(gpio, on) { if(on) gpio.reg->DR_SET = gpio.bit; else gpio.reg->DR_CLEAR = gpio.bit; }
@@ -89,6 +89,9 @@
#ifndef EEPROM_IS_FRAM
#define EEPROM_IS_FRAM 0
#endif
+#ifndef SPINDLE_SYNC_ENABLE
+#define SPINDLE_SYNC_ENABLE 0
+#endif
#ifndef TRINAMIC_ENABLE
#define TRINAMIC_ENABLE 0
#endif
@@ -160,8 +163,8 @@
#include "T40X101_map.h"
#elif defined(BOARD_T41U5XBB)
#include "T41U5XBB_map.h"
-#elif defined(BOARD_T41U5XSS)
- #include "T41U5XSS_map.h"
+#elif defined(BOARD_T41U5XBB_SS)
+ #include "T41U5XBB_ss_map.h"
#elif defined(BOARD_T41PROBB)
#include "T41ProBB_map.h"
#elif defined(BOARD_MY_MACHINE)
@@ -245,46 +248,6 @@
#error "QEI_ENABLE requires encoder input pins A and B to be defined!"
#endif
-typedef enum {
- Input_Probe = 0,
- Input_Reset,
- Input_FeedHold,
- Input_CycleStart,
- Input_SafetyDoor,
- Input_LimitsOverride,
- Input_EStop,
- Input_ModeSelect,
- Input_LimitX,
- Input_LimitX_Max,
- Input_LimitY,
- Input_LimitY_Max,
- Input_LimitZ,
- Input_LimitZ_Max,
- Input_LimitA,
- Input_LimitA_Max,
- Input_LimitB,
- Input_LimitB_Max,
- Input_LimitC,
- Input_LimitC_Max,
- Input_KeypadStrobe,
- Input_QEI_A,
- Input_QEI_B,
- Input_QEI_Select,
- Input_QEI_Index,
- Input_SpindleIndex,
- Input_Aux0,
- Input_Aux1,
- Input_Aux2,
- Input_Aux3
-} input_t;
-
-typedef enum {
- IRQ_Mode_None = 0b00,
- IRQ_Mode_Change = 0b01,
- IRQ_Mode_Rising = 0b10,
- IRQ_Mode_Falling = 0b11
-} irq_mode_t;
-
typedef struct {
volatile uint32_t DR;
volatile uint32_t GDIR;
@@ -306,17 +269,22 @@ typedef struct {
} gpio_t;
typedef struct {
- input_t id;
- uint8_t group;
+ pin_function_t id;
+ pin_group_t group;
uint8_t pin;
gpio_t *port;
gpio_t gpio; // doubled up for now for speed...
- irq_mode_t irq_mode;
+ pin_irq_mode_t irq_mode;
uint8_t offset;
volatile bool active;
volatile bool debounce;
} input_signal_t;
+typedef struct {
+ uint8_t n_pins;
+ input_signal_t *pins;
+} pin_group_pins_t;
+
// The following struct is pulled from the Teensy Library core, Copyright (c) 2019 PJRC.COM, LLC.
typedef struct {
@@ -330,9 +298,12 @@ typedef struct {
void selectStream (stream_type_t stream);
void pinModeOutput (gpio_t *gpio, uint8_t pin);
-
uint32_t xTaskGetTickCount();
+#ifdef HAS_BOARD_INIT
+void board_init(pin_group_pins_t *aux_inputs);
+#endif
+
#ifdef UART_DEBUG
void uart_debug_write (char *s);
#endif
diff --git a/grblHAL_Teensy4/src/generic_map.h b/grblHAL_Teensy4/src/generic_map.h
index bd051dc..ce6f844 100644
--- a/grblHAL_Teensy4/src/generic_map.h
+++ b/grblHAL_Teensy4/src/generic_map.h
@@ -1,9 +1,9 @@
/*
- generic_map.h - driver code for IMXRT1062 processor (on Teensy 4.0 board)
+ generic_map.h - driver code for IMXRT1062 processor (on Teensy 4.x board)
Part of grblHAL
- Copyright (c) 2020 Terje Io
+ Copyright (c) 2020-2021 Terje Io
Grbl is free software: you can redistribute it and/or modify
it under the terms of the GNU General Public License as published by
@@ -19,6 +19,10 @@
along with Grbl. If not, see .
*/
+#if SPINDLE_SYNC_ENABLE
+#error Spindle sync is not supported
+#endif
+
// Define step pulse output pins.
#define X_STEP_PIN (2u)
#define Y_STEP_PIN (4u)
@@ -69,8 +73,8 @@
#if EEPROM_ENABLE || KEYPAD_ENABLE
#define I2C_PORT 4
-#define I2C_SCL4 (24u) // Not used, for info only
-#define I2C_SDA4 (25u) // Not used, for info only
+#define I2C_SCL4 (24u) // Not referenced, for info only
+#define I2C_SDA4 (25u) // Not referenced, for info only
#endif
#if QEI_ENABLE
diff --git a/grblHAL_Teensy4/src/my_machine.h b/grblHAL_Teensy4/src/my_machine.h
index ce499b6..1d33c87 100644
--- a/grblHAL_Teensy4/src/my_machine.h
+++ b/grblHAL_Teensy4/src/my_machine.h
@@ -25,6 +25,7 @@
// If none is enabled pin mappings from generic_map.h will be used
//#define BOARD_T40X101
#define BOARD_T41U5XBB
+//#define BOARD_T41U5XBB_SS // For a modified T41U5XBB board, allows spindle sync to be enabled.
//#define BOARD_CNC_BOOSTERPACK
//#define BOARD_MY_MACHINE // Add my_machine_map.h before enabling this!
@@ -38,7 +39,7 @@ BOARD_T40X101 | no | no | yes | yes
BOARD_T41U5XBB | yes | yes | yes | yes³ | max 5 |
BOARD_CNC_BOOSTERPACK | yes² | yes | yes | yes | max 3 |
-¹ Teensy 4.1 only.
+¹ Teensy 4.1 only
² External magjack.
³ EEPROM is optional and must be added to the board.
@@ -46,21 +47,22 @@ N_AXIS has a default value of 3, edit grbl\config.h to increase.
*/
-#define USB_SERIAL_CDC 2 // 1 for Arduino class library and 2 for PJRC C library. Comment out to use UART communication.
-//#define USB_SERIAL_WAIT 1 // Wait for USB connection before starting grblHAL.
-//#define SPINDLE_HUANYANG 1 // Set to 1 or 2 for Huanyang VFD spindle. Requires spindle plugin.
-//#define QEI_ENABLE 1 // Enable quadrature encoder interfaces. Max value is 1. Requires encoder plugin.
-//#define ETHERNET_ENABLE 1 // Ethernet streaming. Requires networking plugin.
-//#define SDCARD_ENABLE 1 // Run gcode programs from SD card, requires sdcard plugin.
-//#define KEYPAD_ENABLE 1 // I2C keypad for jogging etc., requires keypad plugin.
-//#define PLASMA_ENABLE 1 // Plasma/THC plugin. To be completed.
-//#define PPI_ENABLE 1 // Laser PPI plugin. To be completed.
-//#define ODOMETER_ENABLE 1 // Odometer plugin. To be completed.
-//#define EEPROM_ENABLE 1 // I2C EEPROM support. Set to 1 for 24LC16(2K), 2 for larger sizes. Requires eeprom plugin.
-//#define EEPROM_IS_FRAM 1 // Uncomment when EEPROM is enabled and chip is FRAM, this to remove write delay.
-
-//#define ESTOP_ENABLE 0 // When enabled only real-time report requests will be executed when the reset pin is asserted.
- // Note: if left commented out the default setting is determined from COMPATIBILITY_LEVEL.
+#define USB_SERIAL_CDC 2 // 1 for Arduino class library and 2 for PJRC C library. Comment out to use UART communication.
+//#define USB_SERIAL_WAIT 1 // Wait for USB connection before starting grblHAL.
+//#define SPINDLE_HUANYANG 1 // Set to 1 or 2 for Huanyang VFD spindle. Requires spindle plugin.
+//#define QEI_ENABLE 1 // Enable quadrature encoder interfaces. Max value is 1. Requires encoder plugin.
+//#define ETHERNET_ENABLE 1 // Ethernet streaming. Requires networking plugin.
+//#define SDCARD_ENABLE 1 // Run gcode programs from SD card, requires sdcard plugin.
+//#define KEYPAD_ENABLE 1 // I2C keypad for jogging etc., requires keypad plugin.
+//#define PLASMA_ENABLE 1 // Plasma/THC plugin. To be completed.
+//#define PPI_ENABLE 1 // Laser PPI plugin. To be completed.
+//#define ODOMETER_ENABLE 1 // Odometer plugin. To be completed.
+//#define EEPROM_ENABLE 1 // I2C EEPROM support. Set to 1 for 24LC16(2K), 2 for larger sizes. Requires eeprom plugin.
+//#define EEPROM_IS_FRAM 1 // Uncomment when EEPROM is enabled and chip is FRAM, this to remove write delay.
+//#define SPINDLE_SYNC_ENABLE 1 // Enable spindle sync support (G33, G76). !! NOTE: Alpha quality - enable only for test or verification.
+ // Currently only available for BOARD_T41U5XBB_SS.
+//#define ESTOP_ENABLE 0 // When enabled only real-time report requests will be executed when the reset pin is asserted.
+ // Note: if left commented out the default setting is determined from COMPATIBILITY_LEVEL.
#if ETHERNET_ENABLE > 0
#define TELNET_ENABLE 1 // Telnet daemon - requires Ethernet streaming enabled.